CZ52 9mm barrels

[k98k792]

Aim has them.

http://www.aimsurplus.com/acatalog/CZ52_Accessories.html

[casey439]

Thanks for the heads up will be heading there this morning to pick one up


:sniper:

[NavajoNPaleFace]

I can't tell by the pictures but does anyone know if they come with the roller bearings attached?

I think they are an inexpensive way to get a great plinker going.

[Simon]

Is that a 9x18 or 9x19 barrel?

[rustypirate]

I would think that it would be 9X19 and stripped without rollers or the retaining plate.

[casey439]

ok back from picking up the barrel no rollers or plate just bare barrel looks really good though

cheap way to go for a long day of shooting:
CZ52 pistol $140
http://www.aimsurplus.com/acatalog/CZ52_7_62x25_Pistol.html

1224 rounds of ammo $120
http://www.aimsurplus.com/acatalog/1980_s_Brass_Case_Romanian_762x25_Surplus.html

For down the road:
9mm Luger barrell $50
http://www.aimsurplus.com/acatalog/CZ52_Accessories.html

[GearShanty]

I couldn't resist. Mine just came in on Friday. Seems to hand cycle fine. Will try to get a range report this week.

[kevin]

i bought a bunch of them and have been selling them on auction sites. Now ive got one left for myself and one still on auction. Most sold as buy it now. Used the profits to buy a CZ82. Wish AIM still had barrels, they sold out fast!

[turbothis]

i shot mine some and it did good but had a couple rounds that had trouble getting into the barrel. i think it is because the mag is too long.

[k98k792]

Got my additional parts from Numrich and took it along to the range. Only had time to put four mags through it. All of the mags, two issue and two aftermarket fed perfectly. I shot WWB ball through it.
I had read that the 9mm would shoot pretty high,but was very close to point of aim in my grayback.
Recoil seemed about the same,but not as SHARP.
Best part is I can get ammo anywhere,and clean at my convinence.
Now I need to see how it does with some HP.

[Simon]

Ahg, about my luck that when I finally order a CZ52 that they'd be long out of these. In case they get more later, what all was needed for the conversion? Simply a barrel and some time?

[k98k792]

Roller cam,rollers and rollercam retaining pin.
Kevin 917z may still have one for sale.

[kevin]

i saw some barrels today at a gun show, they wanted 75 each for them

[Woodman in MO]

AIM has these listed again. I don't know if they really have them, but I ordered one and got a confirmation. I can't recall how much they were in May, but I think they went up a little.

Still worth it to me....

[rustypirate]

I picked one up at a local dealer with the locking plate and rollers for $60

[k98k792]

That is a good deal Rusty!
So far mine has worked great.

[GearShanty]

Mine shot well. I had a few feeding issues, but nothing that couldn't be cured through immediate action. I never have shot the CZ-52 well, but the 9mm barrel is consistant with the tokarev barrel.

[kevin]

feeding issue is easy to fix

"The lower 1/2 of the front end of the extractor actually contacts the round, pushing it into the chamber. By smoothing and rounding the angled surface on the lower 1/2 only, the extractor hook will not disrupt the movement of the round as it jumps around the rim of the cartridge being chambered. To remove the extractor, use a small punch to drive the pivot pin through the slide. This will release both the extractor and its spring."

[Rampager]

Does anyone sell the rollers and related parts for these?

[GearShanty]

Numrich has them.
http://www.e-gunparts.com/productschem.asp?chrMasterModel=1300z52%20PISTOL

[k98k792]

Sportsmans Guide has the barrels now.
http://www.sportsmansguide.com/cb/cb.asp?a=359182