WTS: Bill Springfield's trigger services...

[SteelCore]

Howdy, all:

I've been in contact with Bill Springfield, who many of us know by his pheonmenal work on HK/CETME (and other) trigger jobs. I told him I would post his 'services' writeup in this new forum...hopefully he'll stop by and register sometime. Until then, here's the services:

--------------------------------
Here is a list of my services,

Trigger work on HK 91, 93, 94, MP-5 PTR-91, all Century, SW-5, 3 and
all other clones. Trigger creep reduced up to 94%+, rough feel is
smoothed out, pull weight reduced to about 4.75lbs from the factory 10 to 12
lbs pull. $45
-->Minimize trigger slack take up and over travel add $15.
-->HK SEF full auto packs converted to semi $40 (or $30 with trigger job).

Cetme.Trigger creep reduced up to 94%+, rough feel is smoothed out,
pull weight reduced to about 5 lbs from the factory 10 to 12 lbs pull.
Sear bar is unitized to the trigger to eliminate trigger slop. $45, option
to reduce trigger over travel add $4.

Cetme/HK, PTR-91, CAI and all clones: Adjust Ejector for more positive
ejection reliability, quite a few of these rifles do no not allow the
ejector to fully ride up inside the bolt head for positive ejection $8.

SKS, Trigger creep reduced up to 90%+, rough feel is smoothed out, pull
weight reduced to about 4.5 lbs. $27.

M1 Garand, M1A/M14, Ruger Mini-14, Trigger pull lighten up to 15%,
rough feel is smoothed out, nice reduction in trigger creep. $28

AR-15, AR-10, all makes, 3.75 to 4lbs pull, very short, smooth clean
break, trigger staging/creep eliminated $29,
2.75 to 3lbs pull add $14 (JP spring set installed).
Remove hammer tail for better ignition add $5.

Robinson XCR, 3.75 to 4lbs pull, very short, smooth clean break,
trigger staging/creep eliminated $45

Armalite AR180b, 3.75 to 4lbs pull, very short, smooth clean break,
trigger staging/creep eliminated $35

AR180, Sterling, Howa, Costa Mesa sheet metal receiver models: 5lbs,
clean break, no creep. $35

Daewoo .223 all models, 3.75 to 4lbs pull, very short, smooth clean
break, $35

FAL all models, 4.5 to 5lbs pull, very short, smooth, clean break, over
travel significantly reduced $29

Ruger 10/22 2.75 to 3lbs pull, very short, smooth, clean break, $19

Marlin Camp, 4lbs pull, very short, smooth clean break, $35
--------------------------------
For info and shipping instructions & addy, Contact Bill at wspringfield@comcast.net.

Bill's turnaround time is usually a week or less. If you want that battle rifle to group tighter at 200yd, 300yd, or more, Bill's services will make much of the difference. Some CETME owners have said that his trigger jobs were the single best thing they did for their CETME.

[nalioth]

Pimpin'!!

Guys this is good info to know, Bill Springfield does excellent work on triggers of all types of arms.

:thumbup:

[jlpskydive]

Where do I ship my SKS group and one of my AR's that feels like crap?

[snapshot762]

Thanks for posting that SteelCore. I'm currently waiting on a couple of US parts to arrive before sending my PTR91 trigger pack to Mr. Springfield.

[SteelCore]

Email Bill at the email addy I listed there. He can tell ya where to send them.

Tell 'em SteelCore (Keith) sent ya.

[LostInTexas]

Guys, if you don't know, Bill does excellent work! You won't be disappointed. Well maybe that you didn't send it to him sooner!

[bullseye]

Like the man said, it was the single best thing i could have done for mine, made it more accurate and more fun to shoot.

[bataanboy]

I had Bill do my CETME and SKS trigger sets and I can't rave enough about the results. Quick turn around and reasonably priced.

[LorDiego]

I have a Cetme and a Fal, both Century, that I would like to get done.

Can somebody who knows what he is doing post what exactly is to be done in order to send the triggers to this man? A beginner's guide?

Pictures would rock the F. out.

[nalioth]

I have a Cetme and a Fal, both Century, that I would like to get done.

Can somebody who knows what he is doing post what exactly is to be done in order to send the triggers to this man? A beginner's guide?

Pictures would rock the F. out. Email Bill directly at wspringfield@comcast.net

He will tell you what to do.

[SteelCore]

For the SKS trig group, just remove from stock, put it in a plastic bag and in a shipping envelope, send.

In the past for CETME HK91s and G-3s, it was just sen the trigger pack. Now he asks that you send the trigger pack in the lower grip frame as one.

Bill will give you all the details on shipping when you contact him via email.

[bspring]

Thanks for all the kind words guys!

Bill Springfield

[SteelCore]

awesome.

[jfowl31]

Whats a typical turnaround time for an SKS trigger job? My buddy's got a Yugo that was unissued and looks so clean, but has one of the worst triggers Ive felt on an SKS... worse than my old Russian. It would really finish off the rifle to have a clean pull and break to the trigger with none of the grime and slop that it has now.

[SteelCore]

on that, but I think his standard turn-around is about a week.

[snapshot762]

I just got my PTR-91 trigger pack back from Bill. Amazing! Quite possibly the best mony you can spend on your military rifle IMHO. Trigger pull is smooth and light (i don't have a pull scale, but bet it's at about 4 1/2 pounds or so.) No overtravel in the trigger at all. Received it exactly a week after mailing it off.

Thanks again Bill!

[SteelCore]

Bump///

and sent you an email...